This part is a Pressure or Flow Switch for a Hayward HeatPro Pool Heater.. some of the heater model numbers this fits are HP20654T, HP21104TC, HP21404T, HP21124T.. NOte: This pressure switch is not a thread in type it is made be mounted through a hole...

This 1.5HP Impeller fits a Jacuzzi Piranha 4 Stand Wet End Fixed Bracket Motor only and would be found on a motor that is about 15.6-16.0 Amps on a 115V motor or 7.8-9.0 Amps on a 230V motor..... It can be found under the Name Thera-Max or Thera-Flo on...

This part is a Balboa Circuit board replacement for a Master Spa 54418 EL8000 Mach 3 system it is a new board and can be found under several different numbers..If you have a TV in your model do not order this board as the replacement doesn't have support...

This is a 2.5HP Seal, (2) Bearings & Impeller Kit with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Fits Some Watkins Hot Spring...

This is a 2.5HP Seal, (1) Bearing & Impeller Kit with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Fits Some Watkins Hot Spring....

This is a Watkins Wavemaster 8000 or 8200 2.0HP Seal, (2) Bearing & Impeller Kit with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081...

This is a Watkins Wavemaster 8000 or 8200 2.0HP Seal, (1) Bearing & Impeller Kit with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081...

This is a 1.5-1.65HP Seal Kit, (2) Bearing & Impeller for Watkins, Vendor # 4081, Wavemaster Pumps. This Impeller fits between the Face and the Volute of a the Wet End found on some Watkins HotSpring Caldera pumps with Vendor Code 4081 with Numbers...

This is a 1.5-1.65HP Seal Kit, (1) Bearing & Impeller for Watkins, Vendor # 4081, Wavemaster Pumps. This Impeller fits between the Face and the Volute of a the Wet End found on some Watkins HotSpring Caldera pumps with Vendor Code 4081 with Numbers...

  This is a 1HP Seal, (2) Bearing & Impeller Kit for a Watkins 37334 Vendor Code# 4081 Pump with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Wavemaster 48 1.0HP Motor would be about 7-8.0 Amps on high speed at 230V or 11-12...

  This is a 1HP Seal, (1) Bearing & Impeller Kit for a Watkins 37334 Vendor Code# 4081 Pump with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Wavemaster 48 1.0HP Motor would be about 7-8.0 Amps on high speed at 230V or 11-12...

This is a 1HP Impeller for a Wavemaster 5000 Code 4081, 33980, 34677 48 Frame Side Discharge pump. This Impeller fits between the Face and the Volute of a Wavemaster 3000 Series Wet End. I would advise replacing the Seal when you replace the Impeller...