This kit is a 3" Long RADKit® designed to go onto the outside of a 2" fitting and seal off the area between (2) 2" Fittings Outside to Outside.. An example would be if you had a Suction fitting dripping at the glue joint and there is a piece of 2"...

This is a 1.5HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. Note: The three things you need to know to get the...

This part is a Hot Tub Replacement Bottom Drain Inside Wall Fitting with a 3/4" slip fitting on each end which measures about 1" I.D.. This part is on the foam side of the tub and the Fitting screws into this fitting.. You have to stand the hot tub up...

This kits is a Waterway Viper Pump 5.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, (1) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a 14-16 amp motor.....

This kits is a Waterway Viper Pump 4.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp...

This kits is a Waterway Viper Pump 4.0 Impeller, (1) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp...

This kits is a Waterway Viper Pump 4.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp motor.....

This kit is a Waterway Viper 3.0HP Impeller, Seal, (2) Bearing, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... I have found this 3HP pump impeller to be on a 10amp...

This kit is a Waterway Viper 3.0HP Impeller, Seal, (1) Bearing, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... I have found this 3HP pump impeller to be on a 10amp...

This kits is a Waterway Viper Pump 3.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 3HP pump impeller to be on a 10amp motor.....