This Wear Ring only fits Waterway Executive 4 or 5HP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 13/16" thick from front to back or some Intertek impellers... If you have a Waterway Executive 1,2 or 3 Horsepower Wet End it will require...

This Tool is used to install Luxury Micro Jet Body Front Flanges... SEE THE FLANGES AND ALL OTHER RELATED PARTS BELOW HERE:  Wall Fitting Gasket, BWG/Pent Luxury Micro Jet Silicon Small Tube 1/2oz Special Hot Tub Repair Formula for Sealing...

This Jet body Fits an American Products Pentair Luxury Micro Jet that has (2) Tabs to hold it into the Jet Internal.. The Water fitting is  1" Slip glue in Fitting that can be plumbed into one side and capped on the other side or plumbed in series...

This Jet body Fits an American Products Pentair Luxury Micro Jet that has (2) Tabs to hold it into the Jet Internal.. The Water fitting is  1" Slip glue in Fitting that can be plumbed into one side and capped on the other side or plumbed in series...

This part is a 4.0KW Titanium (Best) Heater Element.  This Heater Element features the bend in the back of the element needed to fit the Balboa M-7 heater tubes and has the standard 1-1/4" spacing between the element terminals, center to center...

This part is a Pump Motor Starter Capacitor.. it is a 88-108 MFD or Microfarad.. 250V   This capacitor measures 1-13/16"diameter x 3-3/8" Long  Special Technical Note: The Capacitor is sometimes the cause of your motor not operating but often...

This part is a Complete XP2e 6.3” 1.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 9.0 Amps on High Speed on a 230V...

This part is a Complete XP2e 6.3” 3.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 12.0 Amps on High Speed on a...

This part is a Complete 4HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 14.0 Amps on High Speed on a 230V motor and...

This is a .5HP or 1/2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .5HP Motor that has about 6.0 Amps on High Speed at 230V and 6-7.0 Amps at 115V. This Impeller fits between the Face and the...

(25) Tubing Clamps, Fits Tubing 3/8" I.D. x 1/2"O.D., Double Wire, for Air System Manifolds, Jet Bodies, Pump Bleeders and other items that 3/8" Barbs..  Links to related parts: (1) Tubing Clamp, Fits Tubing 3/8" I.D. x 1/2"O.D., Double Wire, for...

(1) Tubing Clamp, Fits Tubing 3/8" I.D. x 1/2"O.D., Double Wire, for Air System Manifolds, Jet Bodies, Pump Bleeders and other items that 3/8" Barbs..  Self-compensating hose clamp expands/contracts with temperature change Cannot be over/under...