You are buying a 2" Slip X 2" Slip X (4) 1/2" Ports Manifold open style. This part used in tubs where 1/2" softpipe which measures 3/4" OD glues inside the ports and goes to the back of each jet in the tub and 2" Pipe which is 2 3/8" OD is plumb into 2"...

This part is (1) 1/4" X 3/8" Barbed Coupler that fits 3/8" OD , 1/4" ID Clear Hose on one side and 1/2" OD , 3/8" ID on the other side. These are used for connecting Clear Hoses together in Hot Tubs or pools and commonly used in Ozone systems.

You are buying on a 1 1/2" Slip X 1 1/2" Slip Slice Gate Valve. The Valve recieves a 1 1/2" pipe or fitting (Which is about 1 7/8" outside diameter) on each side. This part is used in hot tubs to stop the water so you could service the heater or the pump...

This part is a 2" Slip X 2" Slip X (6) 3/4" Slip Ports Manifold open Flow Through style. This part used in tubs where 3/4" softpipe which is 1" OD glues inside the ports which are 1" ID and goes to the back of each jet in the tub and 2" Pipe which is 2...

This parts is a Sweep 90 2" Slip X 2" Slip PVC Plumbing Fitting. The Sweep 90 ELL receives a 2" fitting on each side which would measure 2 3/8" ID.. You can Glue any 2" fitting to make a tight plumbing application. AFitting Type Sweep Part...

This part is a (1) 1" Slip X 1" Slip Coupler PVC Plumbing Fitting. The Coupler receives a 1" fitting which measures 1 1/4" OD on one side and then receives a 1" fitting which measures 1 1/4" OD on the other side. The inside diameter of each slip side is...

This part is a 1 1/2" MPT Threaded plug that is used in Swimming Pools to block off the 1 1/2" Threaded returns when winterizing to stop water from being in the plumbing system and used on some Sand or De Hayward filter systems. You would simply unscrew...

This part is a 2 1/2" Heater Split Nut which measures 3 9/16" Inside Diameter of the threads and 3" inside the ceneter part that wraps around a heater tube or body. The Heater Flange Split Nut mounts to the heater tube using 2 screws to hold it in place...

This part is a 2" Slip X 2" Slip X (6) 1/2" Ports Manifold open style. This part used in tubs where 1/2" softpipe which measures 3/4" OD glues inside the ports and goes to the back of each jet in the tub and 2" Pipe which is 2 3/8" OD is plumb into 2"...

This is a 1/2" Spigot Plug which measures 3/4" OD it is used to plug off a 1/2" port which measures 3/4" ID on a manifold or other fittings. Note: The style of this part can vary but they will all act as a 1/2" Plug.. 

This Item is a 20Amp Slo Blo MDA Style Ceramic Fuse that measures 1 1/4" Long x 1/4" Wide and is used on some Hot Tub or Pool Boards. This is a smaller automotive style fuse that does not have glass but used ceramic to dissipate heat. You will not be...

This part is a Complete Jet Internal, American Products, Luxury, 3-1/2" face diameter, Roto, Textured Scallop, Gray... Installation Type Snap In Face Diameter 3-1/2" Jet Part Type Internal Diffuser Opening Type 5 Nozzle...