Pump Impellers

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 3.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 3.0hp (or greater) thru bolt motor. Shaft seal sold...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 4.0hp, it is used in an Ultimax pump wet end, and must be installed on a 4.0hp (or greater) thru bolt motor. Click the below links for the...

This part is a Wear Ring that measures 2 5/8" inside Diameter and fits some Aqua-Flo XP2e and Xp3 Impellers except the 3.0HP Xp2e Impeller... That Impeller requires a different Wear Ring which measures 2 3/8" Inside Diameter.. Look at the chart in the...

 Vico/Balboa Ultima Ultra Flo or Ultra Jet Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 3.0hp,which is between 10 and 12 Amps.. it is used in an Ultima, Ultra Jet and/or Ultra Flo pump wet end, and...

This part is a replacement wear ring found in 48 frame 1 1/2" Flo-Master "FMHP" Series Side Discharge and "FMCP" Center Discharge Spa Pumps.. The ring measures about 1 3/4" inside the wear ring and 2 3/16" at the widest part and about 3/4" tall....

Vico Ultima, Ultra Flo Pump Impeller for a 2HP Motor which would have an Amperage of around 10 Amps on High Speed... Closed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 2.0hp, it is used in an Ultima and/or Ultra Flo pump...

This Wear Ring only fits Waterway Executive 1, 2, or 3HP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 1-1/16" thick from front to back... If you have a Waterway Executive 4 or 5 Horsepower Wet End it will require a different wear ring that...

This item is a 3/4HP Waterway HiFlo Pump Impeller "B".. If Your motor is 115V the amperage would be about 11 Amp if 230V it would be about 7 amps..Closed face impeller made for the Hi-Flo side discharge pump by Waterway Plastics. Rated at...