Pump Impellers

// Read This Note First!! NOTE: This Seal will NOT Fit Sundance® or Jacuzzi® Tubs with a Guangdong LX Wet End for those parts click here Jacuzzi® & Sundance® LX Parts This Seal Set is used ONLY in...

This Seal is a (BEST) Silicon Carbide Salt Resistant Upgraded Version of a PS-201 Seal used Primarily in Vico, Sta-Rite and Power Right Wetends. Silicon Carbide’s exceptional wear and chemical resistance, enhanced dry running capability and high...

This part is a (BEST) Silicon Carbide Salt Resistant Verison of a PS-1000 Seal. NOTE: This Seal does not fit a Waterway Viper or EX2 Wet End.. Silicon Carbide’s exceptional wear and chemical resistance, enhanced dry running capability and high...

This is a XP2e 1.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. See the links below for seals, bearing and other parts...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 3/4hp, it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 3/4hp (or greater) thru bolt...

This part is an Impeller for a Sta-Rite DuraJet DJ Wet End that would be called 1.0hp-1.5HP, your motor should be 8.0-9.0Amp at 230V or 16.0 Amps at 115V.. The number on the back of the impeller will be 17400-0021 or 17400-0121 if you have a number on...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 2.0hp,which would be 8-10.0 Amps.. it is used in an Ultimax pump wet end, and must be installed on a 2.0hp (or greater) thru bolt motor...

This Kit is an 1HP Impeller for an Executive 48 Frame Wet End up to 1HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...