Pump Impellers

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

 This part is the slinger found between the impeller and wet end and the shaft going into the pump motor bearing area and is designed to sling water away from the bearing in case of a seal leak at the wet end.. Note: It has to be placed on the motor...

This is a 3HP Impeller with a 2 1/8" Eye with 7/16" Vane Width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor which would have about 12.0A on high speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2...

This Kit is an 5HP Impeller for an Executive 48 Frame Wet End up to 5HP Motor and a 56 Frame Wet End 5HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This is a 1.5HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1.5HP Motor that has about 9.0 Amps on High Speed at 230V and 14.0 Amps at 115V. This Impeller fits between the Face and the Volute of...

This is a 2.5HP Impeller with a 2 1/8" Eye width and 5/16" Vane width and 4" OD for anAqua-Flo 48 or 56 Frame Wet End 2.5HP Motor that is about 11.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet...

This item is a 2 1/8" wear ring that is used between the impeller and the wet end face on Aqua-Flo XP or XP2 Pumps. This wear ring is for all Horse Powers on 48 or 56 frame XP2 Wet Ends. This wear ring serves as a seal between the suction and pressure...

This is a 1.5HP Impeller with a 2 1/8" Eye Width and a 5/16" Vane Width and 4" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor that has about 9.0 Amps at 230V. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet End...

This is a 1HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1HP Motor that has about 8.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This is a 2HP Impeller with a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller fits between the Face and...

This Kit is an 3HP Impeller for an Executive 48 Frame Wet End up to 3HP Motor and a 56 Frame Wet End 3HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...