Pump Impellers

You are purchasing a 1HP Impeller, (1) Standard Bearing and 1000 Seal with Silicon and a Seal Install Tool that fits an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face...

You are buying a Kit that features (1) PS-201 Seal and (2) Bearings that fit most motors that are mated to Vico, Sta-Rite, Dura-Jet and Power Right Pump Wet Ends and The Professor's Silly Juice to seal the seal. This Seal is used in Most Vico,...

This is a 1/15th HP Impeller for an Aqua-Flo Circulation Pump 48 Frame Side or Center Discharge CMHP, CMCP and FMVP Series Wet End. This Impeller fits between the Face and the Volute of an Aqua-Flo CMHP, CMCP and FMVP Series Wet End. I would advise...

This part is an Aqua-Flo XP3 Pump 4.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4.0HP pump impeller to be on a 14 amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 3.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 3.0HP pump impeller to be on a 12amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 2.5HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 2.5HP pump impeller to be on a 10-12amp motor... Click here for...

This part is a Wear Ring that only fits Guangdong LX or LP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 3/4" thick from front to back... WUA Pumps.. Note: When Replacing some original LX Pump faces the wear ring was built into the face....

This is a 4HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

This is a 4HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

You are buying a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo...

This part is an Impeller for a 48fr Vico Ultima or Ultra Flo, 0.50hp, Jet or Circulation Pump... Closed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 1/2hp, it is used in an Ultima and/or Ultra Flo pump wet end, and...

This Part is a 1HP Impeller that fits an E-Series 48 Frame 1 1/2" Center discharge Wet End which is found in hot tubs some but on Above Ground pool pumps many times. This Impeller fits between the Face and the Volute of an E-Series Wet End. I...