Pump Impellers

3.0 HP impeller for the Waterway EX2 pumps assemblies. This impeller is normally found on motors with a 10.7-12.0 amp motor and fits between the Face and the Volute of an EX2 Wet End. I would advise replacing the Seal when you replace the Impeller. The...

Waterway 4 HP Hi-Flo closed faced impeller for Hi-Flo side discharge wetends that have part number 315-1160 on the rear. This impeller will fits motors that have a 230 Volt 12-13 amp rating. The shaft seal for this impeller can be found here Impeller...

This part is a 7 3/8" ID O-Ring only for a 2 1/2" x 2 1/2" WUA500 or SWIM56-15 5 Horse Power 56 Frame Pump Wet End fits Power-Rite Guangdong LX Brand SWIM56-15 Pump Motors only. These pumps usually have the part number Swim56-15 or WUA500 on...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This part is a Kit with Impeller, Seal and Seal Tool for LX 3536 1431701-03 Pump.. Impeller & Seal Kit LX 48 frame 1.5 HP Hotspring   NOTE: If you have a Jacuzzi, Sundance, Thermospa or D1 hot tub with a 6500- number on the label there are no...

This is an Aqua-Flo 39577 2.0HP Seal Kit & Impeller with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some pumps with Vendor Code 4081. Impeller Type   Closed Face Impeller Diameter...

This part is a Kit that features (1) Seal, (1) Bearing, Seal Tool and Silicon that fit a Piranha, Vendor Code 0302, 1.65hp. To Install you should put silicone sealant on the back of the Metal part and gently push it into place. Also the rubber part can...

This is a 1.5HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. Note: The three things you need to know to get the...

This kits is a Waterway Viper Pump 5.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, (1) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a 14-16 amp motor.....

This kits is a Waterway Viper Pump 4.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp...