Pumps and Related Parts

This part is a Pump Motor Starter Capacitor.. it is a 88-108 MFD or Microfarad.. 250V   This capacitor measures 1-13/16"diameter x 3-3/8" Long  Special Technical Note: The Capacitor is sometimes the cause of your motor not operating but often...

This part is a Complete XP2e 6.3” 1.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 9.0 Amps on High Speed on a 230V...

This part is a Complete XP2e 6.3” 3.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 12.0 Amps on High Speed on a...

This part is a Complete 4HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 14.0 Amps on High Speed on a 230V motor and...

This is a .5HP or 1/2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .5HP Motor that has about 6.0 Amps on High Speed at 230V and 6-7.0 Amps at 115V. This Impeller fits between the Face and the...

Aqua-Flo Xp2 6.1" or 6.3"and XP2e Flo-Master Pump Face O-Ring fits around the Face of a Xp2 Pump Face exclusively for An Aqua-Flo Xp2 pump which has 2" inlet and outlet which measures about 3" across the threads... There are (2) Different versions of...

This wear ring measures 2 3/8" inside Diameter and fits only 3.0HP Aqua-Flo XP2e and Xp3 Impellers.. If you have 1.5, 2.0, 2.5 or 4.0HP they require a different Wear Ring which measures 2 5/8" Inside Diameter.. Look at the chart in the photo section...

This part is a 2 1/2" Slip X 2 1/2" Threaded Pump Union with Gasket or O-ring that matches Union. The Union receives a 2 1/2" pipe or fitting on one side which measures about 3" O.D. and then Screws to a 2...

Aqua-Flo XP3 Complete 2.5HP Wet End fits on a Aqua-Flo Xp3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... If you don't need a complete wet end a list of parts are below... Note: All of the below parts fit this...

Aqua-Flo XP3 Complete 3HP Wet End fits on a Aqua-Flo Xp3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... If you don't need a complete wet end a list of parts are below... Note: All of the below parts fit this...

Aqua-Flo XP3 Complete 4HP Wet End fits on a Aqua-Flo Xp3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... If you don't need a complete wet end a list of parts are below... Note: All of the below parts fit this...

Waterway Viper Pump 5.0 Impeller exclusively for a Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a 14-16 amp motor...   Closed face impeller...