Pumps and Related Parts

You are purchasing a 1HP Impeller, (1) Standard Bearing and 1000 Seal with Silicon and a Seal Install Tool that fits an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face...

You are buying a Kit that features (1) PS-201 Seal and (2) Bearings that fit most motors that are mated to Vico, Sta-Rite, Dura-Jet and Power Right Pump Wet Ends and The Professor's Silly Juice to seal the seal. This Seal is used in Most Vico,...

This is a 1/15th HP Impeller for an Aqua-Flo Circulation Pump 48 Frame Side or Center Discharge CMHP, CMCP and FMVP Series Wet End. This Impeller fits between the Face and the Volute of an Aqua-Flo CMHP, CMCP and FMVP Series Wet End. I would advise...

This part is an Aqua-Flo XP3 Pump 4.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4.0HP pump impeller to be on a 14 amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 3.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 3.0HP pump impeller to be on a 12amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 2.5HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 2.5HP pump impeller to be on a 10-12amp motor... Click here for...

This pump is a 115V (2) Speed 10.5 High and 3.2A Low Speed 48 frame 2" x 2" XP2 pump and motor... The 2" inlet and outlet measure about 3" across the threads... Keep in mind if you choose this high amperage pump and have a tub with a wall style 115V plug...

This part is a Wear Ring that only fits Guangdong LX or LP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 3/4" thick from front to back... WUA Pumps.. Note: When Replacing some original LX Pump faces the wear ring was built into the face....

As of 11/2024 Aqua-flo has started to send this pump with a capacitor bump in an odd spot that may affect your installation, see pic 2. In light of that we are now sending this pump assembly out as a separate 10.5 Amp motor and a genuine 2.5 HP XP2...

This is a 4HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

This is a 4HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

You are buying a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo...