Pump Wet Ends and Related Parts

3.0 HP impeller for the Waterway EX2 pumps assemblies. This impeller is normally found on motors with a 10.7-12.0 amp motor and fits between the Face and the Volute of an EX2 Wet End. I would advise replacing the Seal when you replace the Impeller. The...

Shaft seal for the Balboa / ITT Gemini Plus II bath pump. May also fit other Gemini models but we recommend comparing measurements prior to purchase since there may have been variations of this seal used that may not be exact. Shaft Seal Head...

Vico / Balboa Water Group 1.5 HP side discharge Ultima wetend with 1.5" mbt union connections. The 1.5" union connections on this wetend have an overall diameter of 2-3/8". This wetend mounts to a 48 frame thru bolt motor with an amp range of 13.3-16.4...

This part is an Adapter, Drain Plug, Sundance / Jacuzzi, 1/4" MPT x 3/8" Ribbed Barb, Stainless Steel, Less O-Ring.. Used on Various J-200, J-300, J-400, J-500, J-LX Series Spa Pump HeadsO-Ring is Required, Teflon Tape Not Used Click here for the...

This part is a Complete Wet End for Vendor Code 3536 with pump numbers 1431601-03.  This is for Hot Spring Watkins Pumps 2" X 2" 12Amp 230V Vendor Code 3536 only.   If your pump has 1431601 but no (-03) this is not the correct pump...

Waterway 4 HP Hi-Flo closed faced impeller for Hi-Flo side discharge wetends that have part number 315-1160 on the rear. This impeller will fits motors that have a 230 Volt 12-13 amp rating. The shaft seal for this impeller can be found here Impeller...

You are buying a 1.5 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be...

This part is a Complete Verticle Mount Style Waterway Iron- Might or Uni-Might 1/8th HP Wet End that is 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Adjustable Suction Side discharge 48 frame wet end for FMVP pumps only.  This...

This part is a Complete Flo-Master CMCP 1/15HP Aqua-Flo 1-1/2" x 1-1/2" ( Which measures about 2 3/8" Across the Threads) Center discharge 48 frame wet end for 48FR pumps. This wet end is used with a 48 frame motor that would have about 0.6 Amps on a...

This part is a Wet End, Circulation, TheraMax II, 1/15hp, 230v, 1-1/2" Side Discharge, Sundance , Jacuzzi, 02410512-2 or 6500-907.  The Model# on the pump this would fit would be 02410512-2 or 6500-907.. Note: There are variations to pumps with the...

This Replacement LX Wet End for 0974101-03 or 0974001-03 1.5HP 48Fr LX Pump 2" X 2" only that would be about 8.0 Amps at 230V Vendor Code 3536..  It is about 7 1/4"" across the face of the pump, it measures about 7 3/8" from the bottom to the top...

This part is a Pump Bleeder Barb for some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This...