Pump Wet Ends and Related Parts

NOTE: This Part will Fit Sundance® or Jacuzzi® Tubs with a Guangdong LX Wet End if you replace the entire Wet End.  For just internal parts of the wet end you already have click here Jacuzzi® & Sundance® LX...

This Impeller and Seal Kit is used ONLY in a 6500-907 WTC-50M Jacuzzi® Premium or Sundance® Hot Tub Circulation Pump Wet End. The impeller may have the number B432-01, B432-02, B432-03, B432-04, B432-05 on the back. The impeller measures...

This Impeller and Seal Kit is used ONLY in Intertek Impeller & Seal Kit for Circulation Pump, TheraMax II, 1/15hp, 230v, Sundance or Jacuzzi, 02410512-2 or 6500-907 Pumps Only. The impeller may have the number B706-01, B706-02, B706-03, B706-04,...

This Impeller and Seal Kit is used ONLY in Intertek LX 48WTC, 1/8HP, 115 or 230V, WTC0153, Side Discharge Pumps Only. The impeller may have the number B706-01, B706-02, B706-03, B706-04, B706-05 on the back. The impeller measures about 3 5/8" across but...

This Impeller and Seal Kit is used ONLY in Intertek WTC50 Pumps Only. The impeller may have the number B432-01, B432-02, B432-03, B432-04, B432-05 on the back. The impeller measures about 3 5/8" across but the size can vary but this impeller is the...

3.0 HP impeller for the Waterway EX2 pumps assemblies. This impeller is normally found on motors with a 10.7-12.0 amp motor and fits between the Face and the Volute of an EX2 Wet End. I would advise replacing the Seal when you replace the Impeller. The...

Shaft seal for the Balboa / ITT Gemini Plus II bath pump. May also fit other Gemini models but we recommend comparing measurements prior to purchase since there may have been variations of this seal used that may not be exact. Shaft Seal Head...

Vico / Balboa Water Group 1.5 HP side discharge Ultima wetend with 1.5" mbt union connections. The 1.5" union connections on this wetend have an overall diameter of 2-3/8". This wetend mounts to a 48 frame thru bolt motor with an amp range of 13.3-16.4...

This part is an Adapter, Drain Plug, Sundance / Jacuzzi, 1/4" MPT x 3/8" Ribbed Barb, Stainless Steel, Less O-Ring.. Used on Various J-200, J-300, J-400, J-500, J-LX Series Spa Pump HeadsO-Ring is Required, Teflon Tape Not Used Click here for the...

Waterway 4 HP Hi-Flo closed faced impeller for Hi-Flo side discharge wetends that have part number 315-1160 on the rear. This impeller will fits motors that have a 230 Volt 12-13 amp rating. The shaft seal for this impeller can be found here Impeller...

You are buying a 1.5 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be...

This part is a Complete Verticle Mount Style Waterway Iron- Might or Uni-Might 1/8th HP Wet End that is 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Adjustable Suction Side discharge 48 frame wet end for FMVP pumps only.  This...