Pumps and Related Parts

The Waterway center discharge wet end has been discontinued and replaced with the E-Series Center Discharge wet end by the manufacturer. Please be sure which wet end you have as the parts are not interchangeable. The easiest way to identify which wet end...

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This item is a 1/2" Air Bleeder Plug with Fine threads that can be found on the Newer style of a Sta-Rite Dura-Jet DJ Series Wet ends only.  If you need the O-ring for this plug only Click Here: Sta-Rite Pump, New Style Drain...

This Waterway 2.0hp Ex2 Pump is 230v, 2-spd, 48fr, 9.0A, 2"x 2" and it is a perfect XP2 or XP2e Replacement.. This is Waterways answer to an Xp2 pump.. Manufacturer Waterway Pump Model EX2 Speed 2 Speed (2-Spd) Motor...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

This part is a Complete XP2e 6.3” 4.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 14.0 Amps on High Speed on a...

This pump is a Pump, Waterway Executive, 5.0hp, 230v, 2-spd, 56fr, 2-1/2" x 2", OEM This is an unusual pump meaning the suction side is called 2 1/2" and measures about 3 5/8" Across the threads and the Pressure Side is 2" and measures about 3"...

This pump is a 115V 48 Frame 2" X 2" Waterway Executive (2) Speed 1.5HP 13.3Amp on High and 4.1A on Low..  The Pressure and Suction sides measure about 3" edge to Edge across the threads..  The Waterway Executive 48 pump is thermally...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 3.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 3.0hp (or greater) thru bolt motor. Shaft seal sold...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 4.0hp, it is used in an Ultimax pump wet end, and must be installed on a 4.0hp (or greater) thru bolt motor. Click the below links for the...