This part is a Set of (2) Replacement Gasket Only that measures about 1 1/4" Edge to Edge with a 5/8" Center Hole for the "B/C" Coupling on the air jet spa for all some Saluspa or Lay-Z-Spa AirJet™ Hot Tub models (Siena, Miami, Havana, Paris, Palm...

This part is a Replacement Gasket Only that measures about 1 1/4" Edge to Edge with a 5/8" Center Hole for the "B/C" Coupling on the air jet spa for all some Saluspa or Lay-Z-Spa AirJet™ Hot Tub models (Siena, Miami, Havana, Paris, Palm Springs Air...

This item is a 1.0HP Waterway HiFlo Pump Impeller "C" Kit which included the Seal Kit as well.. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 8 amps..Closed face impeller made for the HiFlo side discharge...

This item is a 1.0HP Waterway HiFlo Pump Impeller "C".. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 10 amps..Closed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1...

This is a 2.0HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps on High at 115V. Note: The three things you need to know to get...

This part is a 45 Degree 2" Street X 2"Slip PVC Plumbing Fitting that has a Threaded hole for a Pressure Switch. The Union glues into a 2" fitting on one side and then receives the fitting on the other side. It will Glue into any 2" fitting to make a...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This Part is a Wet End O-Ring for a 48 or 56 Frame Face Plate for a Jacuzzi Premium or Sundance WUA400 6500 Intertek LX Brand Pump Wet End only.. Watch the video for instruction on how to install this part and also how to determine if this...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This item is a 48 Frame Vico Wet End with 2" x 2" inlet and outlet that would measure about 3" across the threads and it has a 3.0HP impeller which would fit a motor that has 10.0-12.0 amps at 230V and there are no 115V motors this fits.. Pump to Motor...

This part is a Tee that is 2"Slip x 2" Slip x 3/4" FPT.. This part is usually found in plumbing with spigot screwed into it.. Note there are 2 Spigot sizes 3/4" and 1/2" Threaded..   If you need a spigot that threads into this tee click this...

This part is a Sta-Rite Dura-Jet Complete 2" X 2" Wet End that fits both 48 or 56 frame motors and would fit a 230V Pump that is 8.0 Amps or a 115V pump that is 12.0 Amps.. The 2" fitting actually measures about 3" Edge to Edge across the threads.. It...