Aqua-Flo Impellers and Parts

  This is a 1.0HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps on High at 115V. Note: The three things you need to know to...

In this Video The Spa Guy shows you how to identify what Impeller you need to replace your Aqua-Flo Xp2 or XP2e pump impeller... Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save

This is a .5HP or 1/2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .5HP Motor that has about 6.0 Amps on High Speed at 230V and 6-7.0 Amps at 115V. This Impeller fits between the Face and the...

Aqua-Flo Xp2 6.1" or 6.3"and XP2e Flo-Master Pump Face O-Ring fits around the Face of a Xp2 Pump Face exclusively for An Aqua-Flo Xp2 pump which has 2" inlet and outlet which measures about 3" across the threads... There are (2) Different versions of...

This wear ring measures 2 3/8" inside Diameter and fits only 3.0HP Aqua-Flo XP2e and Xp3 Impellers.. If you have 1.5, 2.0, 2.5 or 4.0HP they require a different Wear Ring which measures 2 5/8" Inside Diameter.. Look at the chart in the photo section...

In this Video the Spa Guy show you how to install a 200 seal in an Aqua-Flo Wet End.. This is the seal only version... For the full version look in The Spa Guy's How To Video Library.....

In this Video The Spa Guy Repairs a Aqua-Flo XP2e pump that was leaking.. He replaces the seal and impeller and cleans the shaft up.. The bearing was not bad so no need to replace that....

You are buying a Kit that Features (1) PS-200 Seal for Aqua-Flo Pumps and (1) 1/2Oz Tube of The Professor's Silly Juice a Specially Formulated for Hot Tubs Silicon Sealer. This Seal is Used Primarily in Aqua-Flo Wetends and in Waterway " Viper" Wet Ends...

This is a XP2e 1.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. See the links below for seals, bearing and other parts...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

This part is a Wear Ring that measures 2 5/8" inside Diameter and fits some Aqua-Flo XP2e and Xp3 Impellers except the 3.0HP Xp2e Impeller... That Impeller requires a different Wear Ring which measures 2 3/8" Inside Diameter.. Look at the chart in the...

This part is a replacement wear ring found in 48 frame 1 1/2" Flo-Master "FMHP" Series Side Discharge and "FMCP" Center Discharge Spa Pumps.. The ring measures about 1 3/4" inside the wear ring and 2 3/16" at the widest part and about 3/4" tall....