Pump Wet Ends and Related Parts

This is a XP2e 1.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. See the links below for seals, bearing and other parts...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 3/4hp, it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 3/4hp (or greater) thru bolt...

This part is an Impeller for a Sta-Rite DuraJet DJ Wet End that would be called 1.0hp-1.5HP, your motor should be 8.0-9.0Amp at 230V or 16.0 Amps at 115V.. The number on the back of the impeller will be 17400-0021 or 17400-0121 if you have a number on...

Balboa / Sta-Rite Dura-Jet wetend in 3HP. Also known as the DJ this high flow side discharge wetend can be mounted to 48 or 56 frame motors. This side discharge model has 2" unions that will measure 3" across the male threads. The barb fittings on this...

This part is a Complete XP2e 6.3” 2.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 11.0 Amps on High Speed on a...

This Kit is an 1HP Impeller for an Executive 48 Frame Wet End up to 1HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

The Waterway center discharge wet end has been discontinued and replaced with the E-Series Center Discharge wet end by the manufacturer. Please be sure which wet end you have as the parts are not interchangeable. The easiest way to identify which wet end...

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This item is a 1/2" Air Bleeder Plug with Fine threads that can be found on the Newer style of a Sta-Rite Dura-Jet DJ Series Wet ends only.  If you need the O-ring for this plug only Click Here: Sta-Rite Pump, New Style Drain...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...