Pump Wet Ends and Related Parts

This part is a Complete 1.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 9.0 Amps on High Speed on a 230V motor or 13.0...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 1.5hp,which is between 8 and 9 Amps.. it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 1...

This is a XP2e 4.0HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V.   This Impeller fits between the Face and the...

This parts is an Executive 2" Threaded Face plate assembly (Which will measure about 3" Across the Threads) less the O-rings, Screws, Bleeder Plugs and other hardware needed to attach it to the volute..There is another version of the face with a 2 1/2"...

Waterway Hi-Flo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1.5hp, it is used in a Waterway Hi-Flo pump wet end, and must be installed on a 1.5hp (or greater) thru bolt motor. Shaft seal...

This part is a Complete 2HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 10.0 Amps on High Speed on a 230V motor or 16.0...

This is a XP2e 3.0HP Impeller.. The Impeller has a 2 3/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V there are no 115V versions. Note: If your old impeller has a 2 3/8" Eye this is the...

This is a XP2e 2.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

 This part is the slinger found between the impeller and wet end and the shaft going into the pump motor bearing area and is designed to sling water away from the bearing in case of a seal leak at the wet end.. Note: It has to be placed on the motor...