Pumps and Related Parts

This is a XP2e 3.0HP Impeller.. The Impeller has a 2 3/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V there are no 115V versions. Note: If your old impeller has a 2 3/8" Eye this is the...

This is a XP2e 2.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This Listing is for a Waterway Executive 56fr 2 Speed 230V 3 HP 2 1/2" X 2" Pump. Your sticker may say 4HP but based on the chart it is really a 3HP at 12 Amps. This unit features a 2 1/2" X 2" Executive Wet End that can be moved from the 12 O'clock...

 This part is the slinger found between the impeller and wet end and the shaft going into the pump motor bearing area and is designed to sling water away from the bearing in case of a seal leak at the wet end.. Note: It has to be placed on the motor...

This Pump is a Waterway Executive, 3.0hp, 230v, 2-spd, 48fr, 2" x 2", OEM The 2" Fittings measure about 3" edge to edge across the threads..  Spa Pump Features: Executive wet end designed specifically for 48-frame motors Large 6-1/2" diameter...

This is a 3HP Impeller with a 2 1/8" Eye with 7/16" Vane Width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor which would have about 12.0A on high speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2...

This Pump is an Aqua-Flo Replacement Pump for the numbers 36746, 72194, 72197 with a Vendor Code 4081... This pump is a 48Frame 230V 2 Speed with a 2.0 HP Wet End that features a 2" x 2" inlet and outlet Wet End that measures about 3" across the threads....

This part is a Pump Bleeder Barb with O-Ring that is found on some Aqua-Flo Xp2 and Xp2e wet ends but is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part does come with the...

This Listing is for a Waterway Executive 56fr 2 Speed 230V 2 HP 2" X 2" Pump. Your sticker may say 3HP but based on the chart it is really a 2HP at 10 Amps. This unit features a 2" X 2" Executive Wet End that can be moved from the 12 O'clock position...

This Kit is an 5HP Impeller for an Executive 48 Frame Wet End up to 5HP Motor and a 56 Frame Wet End 5HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...