This TSC-35, ECO-3 or K-35 control panel will work with the SSPA or MSPA series and will control three (3) pumps or two (2) pumps and a blower. It has an LED readout and comes with a 10ft cord.The overlay says Pump1 , Pump2 and Blower so if you have a 3...

This Tubing is a 100ft roll of Air or Water Tubing, that measures 1/4" Inside Diameter x 3/8" Outside Diameter... Note: It is very rare to find this tubing in a hot tub so be sure you are choosing the correct stuff.. Air Tubing Inside...

This Tubing is a 50ft roll of Air or Water Tubing, that measures 1/4" Inside Diameter x 3/8" Outside Diameter... Note: It is very rare to find this tubing in a hot tub so be sure you are choosing the correct stuff.. Air Tubing Inside...

This kit is a 3" Long RADKit® designed to go onto the outside of a 2" fitting and seal off the area between (2) 2" Fittings Outside to Outside.. An example would be if you had a Suction fitting dripping at the glue joint and there is a piece of 2"...

This is a 1.5HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. Note: The three things you need to know to get the...

This part is a Hot Tub Replacement Bottom Drain Inside Wall Fitting with a 3/4" slip fitting on each end which measures about 1" I.D.. This part is on the foam side of the tub and the Fitting screws into this fitting.. You have to stand the hot tub up...

This kits is a Waterway Viper Pump 5.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, (1) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a 14-16 amp motor.....

This kits is a Waterway Viper Pump 4.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp...

This kits is a Waterway Viper Pump 4.0 Impeller, (1) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp...

This kits is a Waterway Viper Pump 4.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp motor.....